But to decide how you like things you first need to know what those things are. There are settings that can be set to your liking.
![manage 3d settings manage 3d settings](https://i2.wp.com/crinrict.com/blog/wp-content/uploads/2019/05/HighProfile2.jpg)
Currently, this just means make sure "preferred refresh rate" is set to "highest available", and the "low latency mode" is set to "ultra." That's about it, really. In my experience, the only settings you would ever need to change are for making gsync work better. The answer to this is that there a few things you need to know before you tweak anything. Other than that stock settings should typically be fine though I think - if you're going to use Nvidia's control panel sharpening then you may also want to check their GPU scaling checkbox globally under the sharpen tab (then I enable sharpening on a per game basis if I like the way it looks) since that "may" mean Nvidia sharpens the image post scale instead of pre scale, but I'm not entirely sure since no one's tested that as far as I know.Ĭlick to expand.I see this question pop up every once in a while. Still, if you're playing at 4K with the 3080 you shouldn't be CPU bound I don't think - at 1440p even you would be sometimes though since in those DF videos they found they were still running up against cpu limits in some titles with a 3900X and 2080 Super if I recall correctly.
#MANAGE 3D SETTINGS FULL#
Being CPU limited can be a nasty thing since you won't get full utilization of the GPU and you can get CPU bound microstutter as confirmed by Digital Foundry in some of their videos (like one of their 2080 S reviews and their 3900X review iirc). The default may not be a bad choice though as latency is even more critical in VR titles from what I gather though CPU prerendering has more pros than cons if you're CPU bound going off of posts like CaptaPraelium's FFR write up on the Battlefield V sub for example, but if you're always GPU bound then you can reduce latency by not prerendering.
![manage 3d settings manage 3d settings](https://thepowerpointblog.com/wp-content/uploads/2019/08/Nvidia-2.png)
#MANAGE 3D SETTINGS DRIVER#
The other thing to change if you have G-Sync is to enable nvidia control panel v-sync to ON while turning in game v-sync OFF inline with the blurbuster's g-sync guide (control panel v-sync on globally, v-sync off in game, plus an fps limiter 3 or 4 frames beneath monitor refresh with either rtss, the driver limiter, or an in-game/in-engine limiter so you don't run into the g-sync ceiling - basically the tldr is that v-sync does something different with g-sync on unless you're hitting the g-sync ceiling where standard v-sync engages - look up the article for more on why this is done).Īdditionally I personally set the "prerendered frames setting" for VR games to "Let the 3D application decide" then if I need to change it I do so on a per game basis same as the Low Lag settings which I leave off unless it's a per game thing.
#MANAGE 3D SETTINGS DRIVERS#
I've personally started switching on the G-Sync ON for windowed and fullscreen mode which is not the default (it's fs only by default) as I've not seen issues with it on the most recent drivers (I did have issues with it in the past though so perhaps some game's still exhibit problems in windowed mode + G-Sync, i'm not entirely sure). There seems to be no 'speed' gain or indeed, loss, in adding the visual enhancements.Click to expand.Typically the default control panel settings are mostly fine, but in particular do you have G-Sync? This is in line with enabling anti-aliasing within Revit Options - for me it is less pleasant to look at on screen.Īs with the OP I wondered if anyone had played about with this in Revit - or perhaps it doesn't matter as I quite like the default in Revit (in Lumion on a 2nd monitor though the changes are well worth it). In the end I realised that I quite like the 'softness' of the default (global) settings in Revit, so I changed it back. I tried it today and it works fine, giving a much sharper line and overall display, although a hint that the CPU and/or GPU were working a little harder.
![manage 3d settings manage 3d settings](https://cdn.thefpsreview.com/wp-content/uploads/2019/12/1.png)
I wondered if it was worth setting the same values in Revit.
![manage 3d settings manage 3d settings](https://era20tech.com/wp-content/uploads/2021/09/How-to-set-Nvidia-as-the-default-graphics-card-for-Windows-10.jpg)
I was going to post a topic on the subject but noticed there was already this oneįor a few years I have used the settings for Lumion for my Nvidia cards (currently 2 x Geforce RTX 2080 Ti) given in this youtube video: